|
||||||
Evaluation CategoriesPavement performance is a function of its relative ability to serve traffic over a period of time. Typically, a system of objective measurements is used to quantify a pavement's condition and performance. These systems are used to aid in making the following types of decisions (Hicks and Mahoney, 1981):
RoughnessPavement roughness is an expression of irregularities in the pavement surface that adversely affect a vehicle's ride quality. Roughness is an important pavement characteristic because it affects not only ride quality but also vehicle operating costs, fuel consumption and maintenance costs. The World Bank found road roughness to be a primary factor in the analyses and trade-offs involving road quality vs. user cost (UMTRI, 1998). WSDOT uses the international roughness index (IRI), developed by the World Bank in the 1980s, to quantify roughness. IRI is based on the accumulated suspension of a vehicle (inches or mm) divided by the distance traveled by the vehicle during the measurement (miles or kilometers). The open-ended IRI scale is shown in Figure 1.
Figure 1: IRI Roughness Scale (replotted from Sayers et al., 1986) Roughness measurements can be made in a variety of ways including surveying instruments, portable inclinometers, profilographs, response type road roughness meters (RTRRMs) and profiling devices. The most common methods involve profilographs and profiling devices. For pavement condition surveys, WSDOT makes roughness measurements using laser equipment mounted in their data distress collection van (see Figure 2). In addition to collecting IRI data, this van also records rutting and video images of the pavement surface, ahead view, and shoulder view. Figure 2: WSDOT's Data Distress Collection Van
Surface DistressSurface distress is "Any indication of poor or unfavorable pavement performance or signs of impending failure; any unsatisfactory performance of a pavement short of failure" (Highway Research Board, 1970). Surface distress modes can be broadly classified into the following three groups:
Thus, surface distress will be somewhat related to roughness (the more cracks, distortion and disintegration - the rougher the pavement will be) as well as structural integrity (surface distress can be a sign of impending or current structural problems). Surface distress measurement techniques are largely visual. Simpler, less expensive techniques, use individuals or teams of individuals to subjectively rate pavement sections based on observed distress. More advanced techniques record pavement surface video images at highway speed using high resolution cameras on a specially equipped van (see Figure 2). Evaluation is either done manually by playing the video back on specially designed workstations while trained crews rate the recorded road surface or automatically by computer software.
Skid ResistanceSkid resistance is the force developed when a tire that is prevented from rotating slides along the pavement surface (Highway Research Board, 1972). Skid resistance is an important pavement evaluation parameter because:
Skid resistance changes over time. Typically it increases in the first two years following construction as the asphalt binder is worn away by traffic, then decreases over the remaining pavement life as aggregates become more polished. Skid resistance is also typically higher in the fall and winter and lower in the spring and summer. This seasonal variation is quite significant and can severely skew skid resistance data if not properly compensated (Jayawickrama and Thomas, 1998). WSDOT measures skid resistance using a locked-wheel skid tester (see Figure 3), which basically employs a locked wheel skidding along a tested surface to measure friction resistance.
Figure 3: WSDOT's Locked Wheel Skid Tester
DeflectionThe magnitude and shape of pavement deflection is a function of traffic (type and volume), pavement structural section, temperature affecting the pavement structure and moisture affecting the pavement structure. Thus, many characteristics of a HMA pavement can be determined by measuring its deflection in response to load. Surface deflection is measured as a pavement surface's vertical deflected distance as a result of an applied (either static or dynamic) load. The more advanced measurement devices record this vertical deflection in multiple locations, which provides a more complete characterization of pavement deflection. The area of pavement deflection under and near the load application is collectively known as the "deflection basin". The most common type of measurement equipment in Washington is the falling weight deflectometer (FWD) (see Figures 4 and 5). The FWD can either be mounted in a vehicle or on a trailer and is equipped with a weight and several velocity transducer sensors. To perform a test, the vehicle is stopped and the loading plate (weight) is positioned over the desired location. The sensors are then lowered to the pavement surface, the weight is dropped, and the surrounding pavement vertical deflection is recorded.
|
||||||
